i9+ Receiving Card
Features
- Supports 32 sets of RGB signal parallel output
- Loading capacity: 512×384 pixels
- Supports HDR
- Low latency
- Supports brightness and chromaticity point-by-point calibration
- Supports better gray at low brightness
- Supports color temperature adjustment
- Supports color gamut adjustment
- Seam compensation
- Support any pumping row, pumping column and pumping point
- Supports smart module to save calibration coefficients and other information on module
- Temperature, humidity, power supply control voltage monitoring on cabinet and fan control
- Supports network cable status monitoring
- Supports any scan type from static to 64 scan
- Wide working voltage range with DC 3.3~6V.
- Compatible with all series of Colorlight sending devices
Specification
| Control System Parameters | |
| Sending Device | All series of Colorlight sending devices |
| Control Area of Every Card | Full-color: 512×384 pixels |
| Network Port Exchange | Supported, arbitrary use |
| Gray Level | Maximum 65536 levels |
| Display Module Compatibility | |
| Chip Supports | PWM chips |
| Scan Type | Supports any scan type from static to 64 scan |
| Module Specifications Support | Supports16384 pixels within any row, any column |
| Cable Direction | Supports route from left to right, from right to left, from top to bottom, from bottom to top |
| Data Sets | 32 sets of parallel RGB full color data, 64 sets of serial RGB data |
| Data Folded | Supports 2~8 any discount to improve refresh rate |
| Data Exchange | 32 sets of data any exchange |
| Module Snapshot | Supports any pumping point |
|
Compatible Device and Interface Type |
|
| Communication Distance | UTP cable≤140M；CAT6 cable≤170M；Optic fiber transmission distance unrestricted |
| Compatible with Transmission Equipment | Gigabit switch, fiber transceiver, optical switches |
| Size | 67.6×35.5mm |
| Input Voltage | DC 3.3V~6V |
| Rated Current | 0.5A |
| Rated Power | 2.5W |
| Storage and Transport Temperature | -50℃~125℃ |
| Operating Temperature | -25℃~75℃ |
| Body Static Resistance | 2KV |
| Weight | 9.5g |
| Monitoring Function | |
| Temperature Monitoring |
Cabinet temperature monitoring between -25℃~75℃ 1 port for each card |
| Humidity Monitoring |
Receiver card humidity monitoring between 20%~95% RH 1 port for each card |
| Bit Error Monitoring | Monitor the total number of data packets and error packets to check network quality |
| Supply Voltage Monitoring | 4 ports for supply voltage monitoring |
| Full Color LCD Display Panel | Supported |
| Multi-function card | Monitoring cabinet door, fan and smoke when in conjunction with M3 |
| Pixel Level Calibration | |
| Brightness Calibration | Supported |
| Chromaticity Calibration | Supported |
| Other Features | |
| Hot Backup | Supports loop backup, dual receiver card backup and dual power supply backup |
| Shaped Screen | Supports various freeform display, spherical display, creative display, etc. through the data arbitrary offset |
Hardware
| S/N | Name | Function | Remarks | |
| 1 | Signal indicator light | Flashes once per second |
Receiving card: normal working, Network cable connection: normal |
|
| Flashes 10 times per second | Receiving card: normal working, Cabinet: Sorting & Highlight | |||
| Flashes 4 times per second | Receiving card: Backing up network port (Loop backup status) | |||
| 2 | Power indicator light | The red indicator light shows that the power supply is normal | ||
| 3 | Fixed hole | Used to reinforce the receiving card to improve vibration resistance | ||
| 4 | DDR interface | Connects with display’s HUB board or unit plate | From the diagram above, the left side of the guide plate is first pin (Viewing from the front of card) | |
Definition of Pins
| Instructions | Definition | Pin No. | Definition | Instructions | |
| Ground connection | GND | 1 | 2 | D5V | Power supply |
| GND | 3 | 4 | D5V | ||
| GND | 5 | 6 | D5V | ||
| GND | 7 | 8 | D5V | ||
| GND | 9 | 10 | D5V | ||
| GND | 11 | 12 | D5V | ||
| Do not connect | NC | 13 | 14 | NC | Do not connect |
|
Network port 1 signal pin Recommended use isolation transformer |
eth1_p1 | 15 | 16 | eth2_p1 |
Network port 2 signal pin Recommended use isolation transformer |
| eth1_n1 | 17 | 18 | eth2_n1 | ||
| NC | 19 | 20 | NC | ||
| eth1_n2 | 21 | 22 | eth2_n2 | ||
| eth1_p2 | 23 | 24 | eth2_p2 | ||
| NC | 25 | 26 | NC | ||
| eth1_p3 | 27 | 28 | eth2_p3 | ||
| eth1_n3 | 29 | 30 | eth2_n3 | ||
| NC | 31 | 32 | NC | ||
| eth1_n4 | 33 | 34 | eth2_n4 | ||
| eth1_p4 | 35 | 36 | eth2_p4 | ||
| Do not connect | NC | 37 | 38 | NC | Do not connect |
| Ground connection | GND | 39 | 40 | GND | Ground connection |
| Indicator light | LED_BTN_LED | 41 | 42 | A |
Display control： 1. ABCDE for row decoding signal； 2. LED_LAT for signal lock； 3. LED_OE control LED display enable, like a switch, it is GCLK when the led display use PWM chip |
| Temperature monitoring | LED_TEMP | 43 | 44 | B | |
| Humidity monitoring | LED_HUM | 45 | 46 | C | |
| Fan control | LED_FAN | 47 | 48 | D | |
| Blanking | LED_CTRL | 49 | 50 | E | |
| Serial clock | LED_SCLK | 51 | 52 | LED_LAT | |
| LED_SCLK_S | 53 | 54 | LED_OE | ||
| GND | 55 | 56 | GND | ||
| RGB output | LED_R1 | 57 | 58 | LED_R2 | RGB output |
| LED_G1 | 59 | 60 | LED_G2 | ||
| LED_B1 | 61 | 62 | LED_B2 | ||
| LED_R3 | 63 | 64 | LED_R4 | ||
| LED_G3 | 65 | 66 | LED_G4 | ||
| LED_B3 | 67 | 68 | LED_B4 | ||
| LED_R5 | 69 | 70 | LED_R6 | ||
| LED_G5 | 71 | 72 | LED_G6 | ||
| LED_B5 | 73 | 74 | LED_B6 | ||
| LED_R7 | 75 | 76 | LED_R8 | ||
| LED_G7 | 77 | 78 | LED_G8 | ||
| LED_B7 | 79 | 80 | LED_B8 | ||
| LED_R9 | 81 | 82 | LED_R10 | ||
| LED_G9 | 83 | 84 | LED_G10 | ||
| LED_B9 | 85 | 86 | LED_B10 | ||
| LED_R11 | 87 | 88 | LED_R12 | ||
| LED_G11 | 89 | 90 | LED_G12 | ||
| LED_B11 | 91 | 92 | LED_B12 | ||
| LED_R13 | 93 | 94 | LED_R14 | ||
| LED_G13 | 95 | 96 | LED_G14 | ||
| LED_B13 | 97 | 98 | LED_B14 | ||
| LED_R15 | 99 | 100 | LED_R16 | ||
| LED_G15 | 101 | 102 | LED_G16 | ||
| LED_B15 | 103 | 104 | LED_B16 | ||
| Ground connection | GND | 105 | 106 | GND | Ground connection |
| GND | 107 | 108 | GND | ||
| RGB output | LED_R17 | 109 | 110 | LED_R18 | RGB output |
| LED_G17 | 111 | 112 | LED_G18 | ||
| LED_B17 | 113 | 114 | LED_B18 | ||
| LED_R19 | 115 | 116 | LED_R20 | ||
| LED_G19 | 117 | 118 | LED_G20 | ||
| LED_B19 | 119 | 120 | LED_B20 | ||
| LED_R21 | 121 | 122 | LED_R22 | ||
| LED_G21 | 123 | 124 | LED_G22 | ||
| LED_B21 | 125 | 126 | LED_B22 | ||
| LED_R23 | 127 | 128 | LED_R24 | ||
| LED_G23 | 129 | 130 | LED_G24 | ||
| LED_B23 | 131 | 132 | LED_B24 | ||
| LED_R25 | 133 | 134 | LED_R26 | ||
| LED_G25 | 135 | 136 | LED_G26 | ||
| LED_B25 | 137 | 138 | LED_B26 | ||
| LED_R27 | 139 | 140 | LED_R28 | ||
| LED_G27 | 141 | 142 | LED_G28 | ||
| LED_B27 | 143 | 144 | LED_B28 | ||
| LED_R29 | 145 | 146 | LED_R30 | ||
| LED_G29 | 147 | 148 | LED_G30 | ||
| LED_B29 | 149 | 150 | LED_B30 | ||
| LED_R31 | 151 | 152 | LED_R32 | ||
| LED_G31 | 153 | 154 | LED_G32 | ||
| LED_B31 | 155 | 156 | LED_B32 | ||
| Ground connection | GND | 157 | 158 | GND | Ground connection |
|
Smart module (Save calibration coefficients in module) |
LED_SPI_SCK | 159 | 160 | LED_SPI_SDI |
Smart module (Save calibration coefficients in module) |
| LED_SPI_CS1 | 161 | 162 | LED_SPI_CS2 | ||
| LED_SPI_SDO1 | 163 | 164 | LED_SPI_SDO2 | ||
| LED_SPI_CS3 | 165 | 166 | LED_SPI_CS4 | ||
| LED_SPI_SDO3 | 167 | 168 | LED_SPI_SDO4 | ||
| LED_SPI_CS5 | 169 | 170 | LED_SPI_CS6 | ||
| LED_SPI_SDO5 | 171 | 172 | LED_SPI_SDO6 | ||
| LED_SPI_CS7 | 173 | 174 | LED_SPI_CS8 | ||
| LED_SPI_SDO7 | 175 | 176 | LED_SPI_SDO8 | ||
| Power supply monitoring | LED_M1 | 177 | 178 | LCD_CTRL5 | Reserved |
| LED_M2 | 179 | 180 | RS | LCD | |
| LED_M3 | 181 | 182 | SDA | ||
| LED_M4 | 183 | 184 | SCL | ||
| LED_M5 | 185 | 186 | CS | ||
| Reserved | NC | 187 | 188 | RCV_BK1 | Dual card backup |
| NC | 189 | 190 | RCV_BK2 | ||
| LCD | GPIO0 | 191 | 192 | LED_BLUE | RGB tricolor indicator |
| GPIO1 | 193 | 194 | LED_GREEN | ||
| GPIO2 | 195 | 196 | LED_RED | ||
| GPIO3 | 197 | 198 | RCV_BK6 | Reserved | |
| Ground connection | GND | 199 | 200 | GND | Ground connection |
Figure for Size and Hole Position
Unit：mm
- Last：i9 Receiving Card
- Next：K5 plus Receiving Card
Article KeyWords:i9 plus Receiving Card
Meta:
Article Feed
Sitemap Feed
